|      |  English    
首    頁 產品介紹 走進西磁 新聞中心 產品應用 資料下載 人才招聘 聯系我們

Glossary of Magnet Terminology

Air Gap- Basically the "external" distance from one pole of the magnet to the other though a non-magnetic material (usually air).

Anisotropic- Materials that have a "preferred" magnetization direction. These materials are typically manufactured in the influence of strong magnetic fields, and can only be magnetized through the preferred axis. Neodymium (Iron Boron) and Samarium Cobalt magnets are anisotropic.

B/H Curve- The result of plotting the value of the magnetic field (H) that is applied against the resultant flux density (B) achieved. This curve describes the qualities of any magnetic material.

BHmax (Maximum Energy Product) - The magnetic field strength at the point of maximum energy product of a magnetic material. The field strength of fully saturated magnetic material measured in Mega Gauss Oersteds, MGOe.

Brmax (Residual Induction) - Also called "Residual Flux Density". It is the magnetic induction remaining in a saturated magnetic material after the magnetizing field has been removed. This is the point at which the hysteresis loop crosses the B axis at zero magnetizing force, and represents the maximum flux output from the given magnet material. By definition, this point occurs at zero air gap, and therefore cannot be seen in practical use of magnet materials.

C.G.S. – Abbreviation for the "Centimeter, Grams, Second" system of measurement.

Coercive Force - The demagnetizing force, measured in Oersteds, necessary to reduce observed induction, B, to zero after the magnet has previously been brought to saturation.

Curie Temperature (Tc) - The temperature at which a magnet loses all of its magnetic properties.

Demagnetization Curve - The second quadrant of the hysteresis loop, generally describing the behavior of magnetic characteristics in actual use. Also known as the B-H Curve.

Demagnetization Force - A magnetizing force, typically in the direction opposite to the force used to magnetize it in the first place. Shock, vibration and temperature can also be demagnetizing forces.

Dimensions - The physical size of a magnet including any plating or coating.

Dimensional Tolerance - An allowance, given as a permissible range, in the nominal dimensions of a finished magnet. The purpose of a tolerance is to specify the allowed leeway for imperfections in manufacturing.

Electromagnet - A magnet consisting of a solenoid with an iron core, which has a magnetic field only during the time of current flow through the solenoid.

Ferromagnetic Material - A material that either is a source of magnetic flux or a conductor of magnetic flux. Any ferromagnetic material must have some component of iron, nickel, or cobalt.

Gauss - Unit of magnetic induction, B. Lines of magnetic flux per square centimeter in the C.G.S. system of measurement. Equivalent to lines per square inch in the English system, and Webers per square meter or Tesla in the S.I. system.

Gauss meter - An instrument used to measure the instantaneous value of magnetic induction, B, usually measured in Gauss (C.G.S.).

Gilbert - The unit of magnetomotive force, F, in the C.G.S. system.

Hysteresis Loop - A plot of magnetizing force versus resultant magnetization (also called a B/H curve) of the material as it is successively magnetized to saturation, demagnetized, magnetized in the opposite direction and finally remagnetized. With continued recycles, this plot will be a closed loop which completely describes the characteristics of the magnetic material. The size and shape of this "loop" is important for both hard and soft materials. With soft materials, which are generally used in alternating circuits, the area inside this "loop" should be as thin as possible (it is a measure of energy loss). But with hard materials the "fatter" the loop, the stronger the magnet will be. The first quadrant of the loop (that is +X and +Y) is called the magnetization curve. It is of interest because it shows how much magnetizing force must be applied to saturate a magnet. The second quadrant (+X and -Y) is called the Demagnetization Curve.

發布時間:2014-05-13 16:46:16  

  版權所有:綿陽西磁科技有限公司      地址:四川省綿陽高新區火炬西街北段81號 友情鏈接:
  電話:0816-2868182    電子郵箱:[email protected]   郵編:621000    ICP備案號    
嘀嗒司机赚钱吗 配资交易 手机股票交易软件 河南快三号码遗漏 新手理财怎么赚钱 黑龙江11选五前三 同花顺炒股软件官网 福彩p62怎么玩法 600095股票行 bbin在app怎么下载 股票推荐老师电话销售话术